1. what is remanufacturing?
The remanufacturing industry is a concept compared with the traditional manufacturing industry, as a new industry based on the original industry derived from the manufacturing industries in the global scope although there have been great development but the country level and degree of development gap, did not form a unified explanation or concept. The popular explanation in the general industry is the industry formed by the activities of repairing or repairing parts of machinery or parts that have been used or partially damaged through a series of technological processes. The remanufacturing industry has the following main advantages and value and Industry: a life cycle service plan, keep the cost of service parts supply high price; two, to maintain a high competitive position, protection against new entrants into the market competitors; three, reduce warranty cost, optimize the remanufactured products for warranty replacement; four, improve the life of the terminal management, reduce long-term inventory costs; five, environmental protection, and always adhere to the "recycling" and "green" to support sustainable development.
The earliest "remanufacturing" appeared in 1930s, the United States entered World War II and the great depression, the shortage of funds and resources to force manufacturers and consumers began to accept the concept of "product remanufacturing", especially for the deep influence in the automobile manufacturing industry.
Auto parts
The concept and characteristics in order to further understand the remanufacturing, first need to distinguish between "remanufacturing" and "maintenance overhaul and maintenance, renovation of the two concepts, mainly from the results of the activities, technical level, price level and ownership dimension analysis. By comparing the above can be seen, maintenance and renovation activities in order to "close to the original product", in other words it is a product from first to last; more important is to overhaul and overhaul is just a process of maintenance, the product can not be like the remanufactured products enjoy the new warranty service. Because of these three kinds of activities in the consumer and industry there is a certain degree of confusion, so the maintenance and renovation to a certain extent the main obstacle of remanufacturing industry scale growth and standard establishment, maintenance and repair of low value and technical level affects the choice of consumers, the standard of Korea therefore the development of remanufacturing industry requires supporting the renovation and maintenance industry and pay attention to the difference.
In summary we can see that the remanufacturing industry has three basic characteristics: 1, remanufacturing is the professional repair process for the recovery of the old parts, the so-called professional repair process should follow the national government and relevant organizations standards; 2, remanufacturing products to achieve the same with the original products the quality and level of performance, even to achieve better level in whole or in part, the function module; 3, remanufacturing product requirements to quantify the production, so many manufacturing enterprises need the old parts to pick their own recycling center and dismantling process, and the need to establish a strict production line (the same as the original manufacturing) Daimler has been established; the world's largest range of remanufacturing production base, mainly including the engine, gearbox for electric hydraulic control of the original three production Line。
2. auto parts remanufacturing industry chain
Over 50 vehicles (passenger cars) and light, medium and medium truck components have been used for remanufacturing worldwide. Typical examples are: air conditioning compressor, generator, brake, vernier truck, clutch, crankshaft, electronic control module, pump and so on. The open list of China's development and Reform Commission (the first batch) and the Ministry of industry and information (the first to the five batch) also include engines, gearboxes, starters and generators.
Auto parts
It can be seen from the figure that parts remanufacturing is consistent with the production requirements of the original parts of automobile parts, and there is a certain degree of similarity in the process. The initial process of remanufacturing must start from recycling, but there is a certain rate of loss in the car recycling, because remanufacturing has certain requirements for the original parts, after which cleaning, dismantling, monitoring, classification and other basic processes. In this process, it has gradually realized the process of machine and networking equipment instead of manual inspection and screening.
Overview of -02- auto remanufacturing Market
Global automobile market capacity statistics and analysis basically is based on "four years of the sample period, the sample period and the" auto warranty period (such as a general car warranty time 3-4), once the car use time more than the warranty period there is a need to replace the parts, for remanufacturing industry is an excellent opportunity to access, especially when introduced into the overhaul period, remanufacturing has ushered in a great opportunity for development.
Auto parts
From here you can see it in a sample period in the past, growth in the Asia Pacific region is the fastest (56%), at the same time the market in the Asia Pacific region accounted for the proportion increased from 19% in 2012 to 24% in 2016, it can be seen that the market potential in the Asia Pacific region is very large. European car ownership is relatively large, it includes Turkey and Russia, especially Turkey's growth in recent years is very fast, so from 2012 to 2016 in Eastern Europe grew by about 19%, but its global market capacity is relatively small, only from the original 12% to 13% growth.
1. North America
And from the statistics of 2012, we can see that the North American market is independent of remanufacturing channels